Decokoncept
Bestseller

Ultra Slab System

Ultra Slab 1™

Beton coraz trudniej zatrzeć? Zamiast polewać wodą i ryzykować osłabienie, odspojenia, sięgnij po UltraSlab1

SKU PROD 000005 · 20 l

When finishing a large slab, heat, draughts and low humidity reduce the available working time. Surface moisture is lost more quickly, making an even finish harder for the crew to achieve. UltraSlab1™ helps extend working time and makes trowelling easier.

In stock

1

Unit: op.

Need help? Ask our advisors

Calculate how much you need

Concrete condition / substrate

First coat

m²/20 l
m²/l

You can adjust coverage after a site trial. Starting values come from the product card.

  • When finishing a large slab, heat, draughts and low humidity reduce the available working time. Surface moisture is lost more quickly, making an even finish harder for the crew to achieve. UltraSlab1™ helps extend working time and makes trowelling easier.
  • Colloidal silica technology improves tool lubrication on fresh concrete and reduces evaporation related problems. It reduces the need to add water to the surface, which could weaken the top layer.
  • The ready to use treatment is also suitable for dry shake hardeners and concrete mixes that are harder to trowel. Work it into the concrete during finishing to support a more uniform surface.

FAQ

Questions about this product

Answers matched to this product and its pack sizes.

  • How does Ultra Slab 1 help when laying a new concrete floor?Show answer

    Ultra Slab 1 is a product that supports the placing and troweling of fresh concrete and is used in two stages.

    The first application, immediately after the concrete is placed, reduces water evaporation caused by sun, drafts and high temperature. It helps retain the moisture needed for proper cement setting, supports the setting process and reduces the risk of premature drying of the surface.

    The second application, before power troweling with pans begins, makes the concrete easier to work without the need to add water, which could weaken the top layer. It enables safer use of DST hardening toppings and helps achieve a more even floor colour.

    After troweling is finished, we recommend applying Ultra Slab C, which cures the fresh concrete and provides its initial chemical hardening.

    Benefits for the contractor: easier troweling, a reduced risk of drying out and weakening the surface, safer execution of DST floors and a more uniform appearance of the finished concrete.

  • Can water be added to the concrete surface during troweling?Show answer

    Water should not be added to the concrete surface during troweling! Although in emergency situations contractors sometimes resort to it, it can seriously weaken the top layer of the concrete, especially when DST hardening toppings are used. The consequences can be micro-cracks, so-called crazing, reduced abrasion resistance and even delamination of the surface hardening.


    The solution is Ultra Slab 1. The product reduces overly fast water evaporation, protects the surface from the effects of sun and drafts, and helps retain the right amount of cement paste, which contractors call "butter".


    As a result, the concrete is easier to trowel, the DST topping spreads better, and the contractor can avoid the risky addition of water.


    Ultra Slab 1 eliminates one of the most common causes of problems during troweling, making it easier to produce a durable and even concrete floor.

    używanie wody podczas zacierania posadzki betonowej jest niedozwolone
  • Is Ultra Slab 1 suitable for mechanically troweled floors?Show answer

    Yes! Ultra Slab 1 is particularly recommended for industrial floors that are mechanically troweled, both with DST surface hardening and without topping.

    The product is applied twice while the floor is being made:


    First application: immediately after the concrete is placed. Ultra Slab 1 reduces overly fast water evaporation caused by sun, drafts, wind and high temperature. It helps retain the moisture needed for proper cement hydration and reduces the risk of premature drying of the surface.


    Second application: before power troweling with pans begins. The product improves conditions for mechanical finishing, helping to keep the right amount of cement paste on the surface, which concrete workers call "butter". As a result, the concrete is easier to trowel, and the DST topping is easier to spread and bonds better to the substrate.


    The most important benefit? There is no need to rescue the job by adding water during troweling! Adding water can weaken the near-surface layer, lower the abrasion resistance of the DST hardening and increase the risk of micro-cracks, so-called crazing, and even delamination.


    The complete Ultra Slab system: three stages of concrete protection

    1. Ultra Slab 1: during placing and troweling

    Makes fresh concrete easier to work, reduces moisture loss, improves conditions for applying the DST topping and helps achieve a more even floor colour.

    2. Ultra Slab C: after troweling is finished

    The recommended system product for curing fresh concrete and its initial chemical hardening. It helps retain the moisture needed for proper concrete maturing while densifying its near-surface layer. It increases abrasion resistance and reduces dusting.

    3. Ultra Slab+: additional protection for demanding investors


    For floors with higher operating requirements, it is worth considering additional protection with Ultra Slab+. It complements the system and is intended to achieve a higher standard of surface protection. Its scope of action and application timing should be chosen according to the product data sheet.


    What do the contractor and the investor gain?

    Easier and more efficient mechanical troweling.

    Less need to add water.

    Safer application of DST surface hardening.

    Lower risk of dusting, crazing and surface defects.

    More even colour of the finished floor.

    Proper curing and additional chemical hardening of the concrete.

    The option to extend the system with protection for more demanding facilities.

    Ultra Slab is not only a product that makes troweling easier, but a complete system supporting the execution of a durable concrete floor, from the moment the concrete is placed, through troweling, to curing and additional protection.

  • Is Ultra Slab 1 the new name for C² Trowel Aid?Show answer

    Yes. C² Trowel Aid is the earlier name of the product, and the current name is Ultra Slab 1. In the Decokoncept shop, look for it under the new name.

  • Does Ultra Slab 1 replace curing of fresh concrete?Show answer

    No. Ultra Slab 1 supports the placing and troweling of fresh concrete, reduces overly fast water evaporation and helps achieve an even and durable surface. It does not, however, replace curing after troweling is finished.


    The recommended complementary product in the Ultra Slab system is Ultra Slab C, which combines two important functions: curing fresh concrete and its initial chemical hardening.


    Ultra Slab C helps retain the moisture needed for proper cement hydration while chemically densifying the near-surface layer of the concrete, improving its abrasion resistance and reducing dusting.


    By using Ultra Slab 1 while the floor is being made and Ultra Slab C after troweling is finished, the contractor gets a comprehensive system supporting troweling, curing and hardening of the concrete.

  • Is Ultra Slab 1 suitable for DST hardening topping?Show answer

    Yes, Ultra Slab 1 is particularly recommended when producing concrete floors with DST surface hardening.


    The product reduces water evaporation from fresh concrete and helps retain the right amount of moisture and cement paste, which contractors call "butter". As a result, the DST topping spreads, wets and bonds to the substrate more easily during troweling.


    The greatest advantage is the reduced need to add water to the concrete surface. Adding water during troweling can weaken the DST hardening layer, increase the risk of fine cracks, so-called crazing, and in extreme cases even contribute to delamination of the surface hardening.


    Benefits for the contractor: easier application of the DST topping, more efficient troweling, a more even floor colour and a lower risk of surface defects.


    After troweling is finished, we recommend curing and initial chemical hardening of the floor with Ultra Slab C.

See all FAQ questions